This thermistor sends evaporator temperature signals to the processor. The thermistor must be replaced when replacing Defrost Thermostat the evaporator fan. Complete evaporator fan procedure. Unsnap the evaporator thermistor from the Defrost Heater evaporator and remove it. The defrost heater is located at the bottom of the evaporator.
The defrost heater heats the evaporator in the defrost mode of operation. The thermostat must be replaced when replacing the defrost heater. Complete defrost thermostat procedure. Remove Phillips head defrost heater mounting screws 2. Remove the defrost heater. The evaporator drip pan is located under the evaporator. This pan catches condensation from 6.
Desolder the capillary tube from the the evaporator that is generated during the defrost evaporator. Desolder the suction line. Use a pair of pliers 1. Remove the drip pan. Remove the evaporator. With a file, score the capillary tube just above Screws the soldered section.
Break off the soldered section of the capillary tube. This helps prevent solder from plugging the tube during assembly. Place a new evaporator into the freezer and insert the suction and capillary tube into the GEA evaporator. Braze the suction and capillary tube to evaporator using silver solder. Evaporator Install a replacement dryer. Air is driven across the evaporator coils to produce cold air for the freezer and fresh food Evacuate and recharge the system using compartments.
Remove the lower evaporator fan ductwork. The freezer thermistor is located at the center of 3. Remove the defrost thermostat and evaporator the right wall in the freezer compartment. It sends thermistor. Remove the defrost heater Phillips head 1. With a small flat-blade screwdriver, unlock the screws 2 and remove the heater. Remove the thermistor from the cover and 4 located at the four corners of the disconnect the wire connector.
It provides forced-draft cooling for the condenser coil. Disconnect the supply wire connector. Main Processor Card 3. Slide the solenoid assembly out. The main processor card is located in the back of the unit. This card controls the operation of the unit.
If a fan short has occurred, replace the fan prior to the card or the card will be destroyed. Secure power to the unit.
Disconnect the cable assembly. Disconnect the water tube. To disconnect the quick connect, push the black collar in and pull the tube out. Remove the solenoid. Disconnect the processor cable connectors.
Remove the card by unlocking plastic locks located at the corners of the card. When directed to enter Self Diagnostics, refer to the Self Diagnostics section of this chapter for more information. When directed to perform a diagnostic test example; encoder test 0 5 , refer to Table 2, Diagnostic Key Sequences, for more information.
A display can be illuminated by pressing an adjacent temperature adjustment button. When both displays are illuminated, set the freezer and refrigerator temperature settings to 5. Simultaneously press and hold all 4 temperature adjustment buttons for approximately 3 seconds. A flashing 0 in the refrigerator and freezer displays will indicate that the refrigerator is in Self Diagnostic mode. To perform a self diagnostic test, locate the test in Table 2, Diagnostic Tests.
Use the freezer temperature adjustment buttons to enter the test code number in the freezer display. Use the refrigerator temperature adjustment buttons to enter the test code number in the refrigerator display.
When a test code has been entered, the displays will flash to confirm the test. Press the HOLD button for 3 seconds to begin the test. When a test code has been entered, the displays will flash to confirm the test code. Press any button other than a temperature adjust button to begin the test. The temperature control panel is reset automatically. Test mode will terminate when the refrigerator is plugged back in.
Test mode will terminate automatically after 15 minutes of inactivity. This places the freezer in pre-chill mode. The 1 3 Enter pre-chill refrigerator will return to normal operation on its own. This will set the refrigerator into the defrost mode. If the cabinet is not cold when executed, this mode may 1 4 Enter defrost execute extremely fast.
The refrigerator will return to normal operation on its own. Causes system to exit test mode and resets 1 6 Test mode exit temperature control panel. Communication Tests 0 2, 0 3, or 0 4 A communication test will display the test code while checking communication.
When the test has concluded, the freezer display will display a P passed or an F failed for 2 seconds. After 2 seconds, the displays will show the test code. At this time, a new test code can be entered. Temperature Control Panel Self-Test 0 6 This test applies only to the temperature control board inside the fresh food compartment.
The colder key is to turn off seven-segment LEDs. The warmer key is to turn off the Set LED for both the freezer and the fresh food compartments. To exit the Temperature Control Panel Self-Test, both of the refrigerator temperature adjust keys must be pressed simultaneously for 3 seconds. This can be done at any time to exit the test. Dispenser board operation is tested by pressing each button and checking for proper operation. Control and Sensor System Self-Test 0 7 This test checks all five thermistors located throughout the unit.
Once the test is initiated, the test code 0 7 will stop flashing and the thermistor test results will appear on the freezer display in the test order listed below. The thermistor test sequence number will not be shown on the display. If the unit is not equipped with the Quick Chill option, the third thermistor quick chill will display a 0 and 3 audible beeps will sound at the temperature control panel.
This is not a failure if the unit is not equipped with the Quick Chill option. Fresh food top thermistor 2. Fresh food bottom thermistor 3. Quick chill thermistor displays 0 if unit is not equipped with Quick Chill option 4. Evaporator thermistor 5. Freezer thermistor Note: Thermistor test results will be displayed in the sequence shown above.
No Check house supply voltage. Yes connector at rear of unit. No power cord Do you have VAC? Do you have VAC? Yes Replace control board and check all fan motors circuit for shorts. If short Check dispenser and temperature Check for 12 VDC at Unplug J2 connector from is dectected repair short or replace fan control lights!
No control board pin J to No control board. Failure to replace shorted Do they work? J Do you have voltage component will damage the new control board upon installation Yes Yes Short in fan motorcircuits! Caution: Unplug power when disconnecting and connecting connectors on the board. Repair as No Door switch - light turning off with door closed? Yes Turn unit off then back on! Run service diagnostic test No Did the damper cycle?
Damper test - see page 48 Yes Run service diagnostic test Is the Fresh food fan running? Yes Go to Damper flowchart page 48 Is damper closed? No Damper should be closed when FF temperature below normal! Yes Check sealed system Repair Normal frost pattern on No sealed system evaporator? Check temperature setting of Is the compressor running? Yes compressor. No compressor! Do you have VAC Did it start? Yes Look elsewhere for the Does it move?
No Replace damper Does the damper door move? Yes Check continuity at connector J3. Check for same resistance Damper motor defective ohms J to J? No No values at damper motor replace motor ohms J to J? Do you have the correct voltage? No Replace the main board You can only read voltage during 10 seconds of intial start up Yes Replace damper Caution: Unplug power when disconnecting and connecting connectors on the board.
Condenser fan OK! Is the condenser fan running? Yes Look elsewhere for the problem. No Condensor motor stalled! Yes Repair or replace condenser motor. Remove J2 connector from the main board. Check for voltage at main board Check for resistance between the white J2. No No Replace main board Measure the resistance directly at the Condenser fan motor! Yes Repair wiring harness Is the resistance approximatelty 1. No Does the condenser fan motor read Replace the condenser Yes open?
No Replace main board and condenser fan motor Caution: Unplug power when disconnecting and connecting connectors on the board. Yes harness. Does circuit read open? No Yes Check wiring to Evaporator fan Measure resistance directly at fan motor. Repair motor Is the resistance approximaterly Yes wiring 1. Yes Replace fan motor No Check voltage at main board J2. Does the fan motor read shorted? No Replace main board and fan motor Caution: Unplug power when disconnecting and connecting connectors on the board.
Is the resistance approximately? Repair wiring Yes Is the resistance approximatley harness? No Replace main board and FF fan motor Caution: Unplug power when disconnecting and connecting connectors on the board. Measure between blue wire on Measure for VAC Yes defrost terminal J9 on main Yes Yes defrost connector and neutral orange wire on main at defrost heater.
Normal Operating Sounds. Consumer Support. Back Cover. Per formance Data Sheet. Product Registration. State of California W ater. T reatment Device Certificate. W arranty Canadian. W arranty U. Ask a question. Related product manuals. How do I prevent drops from forming on the glass plates of my fridge?
Page 13 Electronic sensors Five electronic sensors consistently measure air temperature. Multiflow air system GE Exclusive! Evenly delivers air throughout the fresh food and freezer compartments.. Adjustable humidity crispers Customizes the storage environment to keep fruits and vegetables fresh. Page 14 GE. To achieve a custom look, you can order wood cabinets. They align with counters, instantly look panels from your cabinetmaker.
Available in white, Available in white, stainless steel handles. Conventional refrigeration uses only one evaporator that cools the freezer, venting cold, dry air into the fresh food compartment. Page 17 The air inside a refrigerator makes a noticeable difference in foods freshness and flavor. When air is allowed quality. By to flow between the fresh food and freezer compartments, it can affect humidity levels and food keeping the air flow separate, the ClimateKeeper2 system helps protect food and ice to keep anything from being wasted.
Air is never mixed between the two compartments. Page 19 Fewer defrost cycles 8 hours 8 hours 8 hours 8 hours 8 hours Traditional 8-hour defrost cycle 10 hours 10 hours 10 hours 10 hours ClimateKeeper2 hour defrost cycle Profile Arctica uses an Adaptive Defrost System which operates on an 8-hour minimal defrost cycle.
ClimateKeeper system The ClimateKeeper system always has three critical features—digital electronic controls, electronic temperature sensors and a multiflow air tower. Invite the customer to after frequent or extended door openings and when hot items press the button, noting how the are placed inside.
Deli drawer The fan will run for 48 hours or until the Quick Ice button is turned off whichever comes first. Great for parties, picnics, etc. Page Tall Lighttouch! Unique, single-cradle design requires only the slightest touch Invite the customer to touch the to activate.
Easy activation along with the tall design allows for single cradle and let them feel easy fill-ups of pitchers, blenders, sports bottles, and coffee pots. Page Spillproof Shelves Slide-out, spillproof shelves Selling Tip: Explain the benefits of easy cleanup by pointing to These tempered glass shelves allow easy access to food the lip on the shelf and items.
Cleanup is simple, too. These shelves will hold spilled explaining how it catches spills. Light shines in the front, right where you need it! Mid-level lights highlight items below. Dual level lighting has one watt upper light and two watt mid-lights. Single level lighting consists of a watt bulb at the top of the fresh food cabinet. Page 33 The icemaker turns on-off by a switch and the feeler arm detects when the ice drawer is full. Page 34 Slide-out, spillproof integrated shelves Selling Tip: Explain the benefits of easy cleanup by high-end GE pointing to the lip on the shelf These tempered glass shelves allow easy access to food items.
The fold-down, two-liter bottles already in place ABS door provides a sturdy serving counter. Page 37 CleanSteel and it blends beautifully with other stainless appliances in the kitchen. Sell food preservation Electronic touch temperature controls GE Exclusive! Electronic temperature sensors allow for better temperature management in the fresh food and freezer compartments, keeping foods fresh.
The visual The difference between and exteriors is dramatic! The larger sculptured Profile handles dramatically change the appearance. Page 39 A check valve stops water flow and prevents leakage.
0コメント